FOMAPAN R 100 General FOMAPAN R 100 is a panchromatic black-and-white reversal film intended for taking  black-and-white slides and/or for making movies. Characteristic  The nominal film speed is ISO 100/21o.  Due to a undercoated very effective silber antihalo layer the film features very good resolving power and high contour sharpness. This antihalo layer will be decolorised during the developing processing.  FOMAPAN R 100 is produced on a cellulose triacetate safety film base of a thickness of 0,125 mm suitable when high mechanical and dimensional stability and high life expectancy are required.  Development   For the optimum results following the processing is recommended :

	Bath Time (min) Temperatur e oC 1 1st developing Fomadon LQR (1+10) 9 - 11 20±0,5 2 washing 10 20±3,0 3 bleaching 5 20±0,5 4 washing 5 20±3,0 5 cleaning bath 3 20±0,5 6 washing 5 20±3,0 7 reexposure 3 20±3,0 8  2nd deveping Fomadon LQR (1+10) 9 20±0,5 9 washing 10 20±3,0 10 fixing 9 20±3,0 11 washing 30 20±3,0 12 drying

	Processing Bath components
	Reversal bath

	1 Water 900 ml 2 Calgon M 19 or Chelaton III 1,5 g 5,0 g 3 SnCl2 1,65 g 4 p-aminophenol HCI 0,66 g 5 NaOH 4,8 g 6 Acetic Acid 11,0 ml

	Cleaning bath

	1 K2S2O3 50,0 g 2 Water to 1000 ml

	bleaching bath

	1 K2Cr2O7 5,0 g 2 H2SO4 10,0 g 3 Water to 1000 ml

	Fixer FU-5

	1 Na2S2O3 250 g 2 K2S2O5 25 g 3 Water to 1000 ml

Safelights
Total darkness or infrared light is recommended until the washing before reexposure

 (the 6th  step of processing). However, i f a illumination is necessary, it is possible to

use a safelight fitted with Agfa 108 filter (15 W bulb, indirect light, at least 150 cm distance from the workplace)

Resolving Power 115  lines per mm

Granularity (RMS) = 13,0

Sizes
This material is usually produced as 
• 16 mm size film, perforated one-side or double-side 
• 2 x 8 mm film (standard) DS 8 film (2x Super 8 mm) 
• 35 mm film perforated double-side 

Storage
The unexposed material should be stored in the original packing at a temperature from 4 ^o C to 18 ^oC and a relative humidity less than 60% out of reach of harmful steams, gases and ionizing radiation. After a long term storage at a low temperature before usage the film shall be kept for about 4 hours at the ambient temperature in the room where it is going to be handled. The exposed material should be processed as soon as possible. In case this condition cannot be kept the film should be stored at a temperature from 4 ^o C to 18^oC and a relative humidity less than 60 % out of reach of harmful steams, gases and ionizing radiation. The processed material can be usually stored at a temperature not more than 21^oC and a  relative humidity from 40 to 50%. For a long term storage such as in archives, special provisions of the corresponding institutions should be kept. 

This product is manufactured and marketed in conformity with a quality system according to the international standard ÈSN EN ISO 9001

All content is copyright protected. No reprint or reposting without our  permission. (C) 1992-2004 by Mirko Böddecker. ADOX, ADOLUX, ADOX adding the grey to black  and white, ADOX fine print, ADOFILE, Vario Classic and efke are registered trademarks of Mirko Böddecker Fotoimpex, Germany,

All other trademarks used are the copyright of their respective owners.